%$#&"!
The A-AU Automatic Spray Gun, is a light duty air actuated
production spray gun. It will cover a range of materials to include
light lacquers, latex, acid or corrosives. )309?=492B>09=4:9=
8,>0<4,78?=>-0;<0==?<010/1:<;<:;0<,;;74.,>4:9
"!!&"!%
Connections to the gun are: Air Inlet 1/4" N.P.T. (F) and Fluid
Inlet 1/4" N.P.T. (M). A-AU Automatic Spray Gun dimensions are:
5-1/8" (L) x 2-1/4" (D)
#!)%$%
Washers are made of leather and treated in oil. For PTFE
Packings see parts list, Page 3.
"#$&"!
1. Mount Gun in desired position
2. Before installing, blow out air hoses with compressed air to
remove foreign particles.
3. Connect hose from air supply to air inlet fitting.
4. Connect fluid hose to fluid inlet supply.
5. Tighten all hose connections securely.
6. Adjust air pressure to 45-55 P.S.I. at the Air Regulator.
7. Adjust fluid volume by turning the U-3178 Fluid Adjusting
Knob to the left or right.
!"&"!"&'%'%%'&"+&'$!!
&)+")!& +%#&&&#
&#$ "(
1. Turn off Air and Fluid Pressure.
2. Release Needle pressure from the seat of Tip, by backing
off the U-3178 Fluid Adjusting Knob approximately 5 turns,
then removing U-2686A Cylinder Cap Assembly.
3. Loosen AU-12 Aircap Nut and remove Spray Head
Assembly. 0,@0!00/709#7,.0
4. Unscrew AU-Tip. Place New AU-Tip in position.
5. To replace, reverse above procedure.
!&!!
Requirements of the A-AU Automatic Spray Gun have been
reduced to a minimum. The leather packing washers should be
lubricated once a month with a light oil. Old Packing Washers
cause leakage of Air or Fluid and replacement should be made.
PTFE Packings are self-lubricating.
'
?>:8,>4.%;<,C?9
"#$&!!%&$'&"!%!$# !&#$&%
!%&$'&"!%#$&%%&'
Supersedes Instructions & Parts List A-AU-6/2008
#,,=.304<-<?=3:8;,9C
4311 North Normandy Avenue
Chicago, IL 60634-1395
#3:90 773-867-9191 F ,B 773-867-9198
)0-=4>0;,,=.30,4<-<?=3.:8
,47491:;,,=.30,4<-<?=3.:8
Printed in the U.S.A.
)$!! Spray materials may be harmful if inhaled or
allowed to come into contact with the skin or eyes. Consult
the product label and Material Safety Data Sheet supplied
for the spray material. Follow all safety precautions.
'&"! Well Ventilated Area Required to remove
fumes, dust or overspray. Secure airhose and fluid
hose wrench tight for safety and to prevent leaks.
, B 4 8 ? 8 4 < # < 0 = = ? < 0 # %
, B 4 8 ? 8 7 ? 4 / # < 0 = = ? < 0 # %
!!
Flush clean solvent through the Fluid passages of the Spray Gun
and Wipe off the outside with clean solvent. Never leave the
entire Spray Gun immersed in solvent. Dirty Aircaps and Tips
should be cleaned by soaking in solvent and blown clean with air.
&$"'%""&!%#$+#&&$!%
(A) $"'"$%&##!% is due to low or restricted flow of air
pressure or too heavy materials being applied with spray gun too close
to surface.
(B) )&"$%!!% is due to low air pressure or restricted
flow of air, material being too thin, applied too close to the surface.
(C) %#'&&$!%#$+ is caused by air leaking into fluid line or can
be caused by a loose fluid tip, a broken or split tip, lumpy material, a
clogged vent hole in cover of material cup, air leak at fluid pipe
attached to inside of tank cover, or a clogged paint strainer.
&""$$& Tighten tip securely or replace. Strain materials and
clean strainer. Sputtering might also be caused by worn packing
washers, or worn or scored needle.
(D) ! $ ! %#$+ #&&$! is caused by dried material
accumulated in one fan port of the fan aircap distorting the pattern.
&""$$&: Dissolve material inside fan port with suitable solvent
applied with a small brush.
!"&!0@0<?=0A4<0:<=3,<;49=><?809>=>:.70,91,9;:<>=,=
;0<8,909> /,8,20 >: >30 ,4< ;:<>= A477 <0=?7> 49 /0=><:C492
?941:<84>C:1>301,9;,>>0<9
(E) '!!!%#$+#&&$!, heavy on one side, may be
caused by material collecting around outside of the fluid tip and
aircap, or by a loose aircap.
&" "$$& Remove aircap and clean fluid tip and aircap with
solvent, dry with air pressure. Always be sure fan aircap and aircap
body is tightened securely.
(F) (+ !&$ in a fan pattern is caused by insufficient air
pressure at the fan port. Rough or shady edges are also caused by
low air pressure.
&""$$&Increase air line pressure.
(G) %#&!%#$+#&&$!heavy on each end and light in the
center, is caused by excessive air pressure.
&""$$&Reduce air pressure.
(1 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern